Futek CSG110 (JM-2A / JM-2AD)-Series Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Czujniki Futek CSG110 (JM-2A / JM-2AD)-Series. FUTEK CSG110 (JM-2A / JM-2AD)-Series User Manual Instrukcja obsługi

  • Pobierz
  • Dodaj do moich podręczników
  • Drukuj
Przeglądanie stron 0
Quick Start Guide
Sensor Solutions Source
Load · Torque · Pressure · Multi-Axis · Calibration · Instruments · Software
www.futek.com
CSG110
Strain Gauge Universal Amplifier
Przeglądanie stron 0
1 2 3 4 5 6 ... 23 24

Podsumowanie treści

Strona 1 - Quick Start Guide

Quick Start GuideSensor Solutions SourceLoad · Torque · Pressure · Multi-Axis · Calibration · Instruments · Softwarewww.futek.comCSG110Strain Gauge Un

Strona 2 - Getting Help

101. The voltage output of the CSG110 is passed through a current converting phase. This means the prior Ex-citation and Gain setting steps of the vo

Strona 3 - Table of Contents

11SW5 SW6 SW7 Input Range Output Range▼ ▼ ▼0–10 V 4–20 mA▼ ▼ ▲0–10 V 5–25 mA▲ ▼ ▼0–10 V 0–16 mA▲ ▼ ▲0–10 V 0–20 mA▼ ▲ ▼0–5 V 4–20 mA▼ ▲ ▲0–5 V 5–25 mA

Strona 4 - Logic Board Configuration

12DIP Switch 1: Excitation• The Excitation is the voltage supplied from the CSG110 to the sensor and can be 5 VDC or 10 VDC.• It is recommended to u

Strona 5 - FEMALE DB9 SENSOR SIDE

13DIP Switch 3: Sensitivity (Gain)• The Sensitivy DIP switch controls the gain needed to obtain the desired output level from the CSG110. For example

Strona 6 - Sensor DB9 Assembly

14DIP Switch 5, 6, and 7: Current Setting• The voltage output from the CSG110 is passed through a current conversion phase. As a result the current o

Strona 7 - CSG110 Power Side Connections

15Shunt is used to simulate a load on the sensor by using an internal resistor labeled ‘RSH’ on the CSG110 circuit board. The resistor will be connect

Strona 8 - Included Power Side DB9 Cable

163 For FSH03546: Min. Power Supply is 12.5 VDC4 Only for sensitivity of 1 mV/V or greater5 Only for sensitivity of 1.5 mV/V or greaterVERSIONSITEM #

Strona 9 - Voltage Setup Steps

17SpecificationsENVIRONMENTPARAMETER MIN TYPICAL MAX UNITOperating Temperature32 158 °F0 70 °CStorage Temperature –40 185 °F–40 85 °CRelative Humidity

Strona 10 - Current Setup Steps

186 Minimum power supply varies for OEM models7 No load applied (input or output)ELECTRICAL SPECIFICATIONSPARAMETER MIN TYPICAL MAX UNITPower Supply61

Strona 11

19ELECTRICAL SPECIFICATIONS (CONTINUED)PARAMETER MIN TYPICAL MAX UNITNoise 15 mV p-pOutput Span Range –10 10 % of Rated OutputOutput Zero R

Strona 12 - DIP Switch Description

2Getting HelpJM-A2/D.12-13-0.0FUTEK reserves the right to modify its design and specifications without notice. Please visit http://www.futek.com/sales

Strona 13

20Related AccessoriesYELLOW MOLDED BOOT (INCLUDED) Item Number: FSH03219SHUNT RESISTORItem Number: Visit WebsiteSCREW TERMINAL (MALE)Item Number: FSH0

Strona 14

21To prevent damage, make sure all connections to the CSG110 are completed before turning on the power to the CSG110.It is best to troubleshoot the CS

Strona 15 - Shunt Resistor

22The CSG110 has no output or low, non-changing output.1. Confirm the power to the CSG110 is between 14 and 26 VDC.2. Confirm there is not a short

Strona 17

10 Thomas, Irvine, CA 92618 USATel: (949) 465-0900Fax: (949) 465-0905www.futek.com

Strona 18

3Getting Help . . . . . . . . . . . . . . . . . . . . . . . 2Logic Board Configuration . . . . . . . . . . . . . . . . 4CSG110 Sensor Side Connections

Strona 19

4Logic Board ConfigurationExcitationPolarityGainCurrent SettingCurrent Input RangeCurrent SettingShuntSWSWSWSWSWSWSW1235678FEMALE MALE21 386 75

Strona 20 - Related Accessories

5CSG110 Sensor Side ConnectionsFEMALE DB9 SENSOR SIDEPIN # WIRING CODE1 + EXCITATION12 + SIGNAL 3 – SIGNAL 4 – EXCITATION1 5 GROUND6 GROUND7 GROUND8 G

Strona 21 - Troubleshooting Tips

6Sensor DB9 AssemblyMALE DB9 CONNECTOR (SUPPLIED)Top CoverNutsDB9 ScrewsCover ScrewsSet ScrewBottom CoverDB9 MaleWasher CoversInformation about your s

Strona 22

7CSG110 Power Side Connections1 2 3 4 56 7 8 92 Only available with current output option. Note: All grounds are connected together and pass through t

Strona 23

8Included Power Side DB9 Cable5 4 3 2 19 8 7 6FEMALE DB9 POWER SIDE (SUPPLIED)PIN # WIRING CODE CABLE COLOR CODE1 SIGNAL OUT (CURRENT) WHITE2 RETURN

Strona 24 - Tel: (949) 465-0900

91. Set SW 1 down for 10 VDC excitation or up for 5 VDC excitation. By default the CSG110 is set to 10 VDC at FUTEK.2. Set the gain DIP switch (SW3)

Komentarze do niniejszej Instrukcji

Brak uwag